SAFETY IN

 

       SAFETY IN DESIGN & ENGINEERING,

         ONSHORE  AND OFFSHORE PRODUCTION FACILITY

 

8-12 October 2018

IKEJA LAGOS.

 

 

COURSE INTRODUCTION

 

It is self-evident that the development of onshore and offshore oil and gas production installation can never be completely “inherently safe”. Nevertheless, the degree of inherent safety can be maximized at the concept and detailed engineering selection stages. Maximising inherent safety and add-on loss prevention package of a design requires identification and assessment of the major risk contributors early in the design phase of the project life thereby allowing their control in a cost beneficial manner.

This requires a structured hazard identification study followed ideally by some form of Quantified Risk Assessment (QRA) which is both accurate and rapid. In the absence of some form of QRA early in the life of the project.

 

Following the above it has become necessary for all engineers involved in the design, construction, installation and maintenance of onshore and offshore production facilities to understand and apply the basic safety in design principles and requirements in their respective disciplines and roles with the sole aim to reduce risk as low as reasonably practicable (ALARP) throughout the life cycle of the asset.

 

In addition, best industry practice and legislation requires engineers to consider the potential risks involved during the design phase of a facility so as to ensure that it is safe to build, operate, maintain and demolish.

The course content is in line with best industry applicable Recognized and Generally Acceptable Good Engineering practice (REGAGEP).


 

COURSE OUTLINE AND DURATION

This is a comprehensive 5 days technical course to be taught by experienced and hands on facilitators with an average of 15-25 years in the oil and gas industry.

The course will involve technical analysis of designs and relevant calculations based on applicable Recognized And Generally Acceptable Good Engineering Practices (RAGAGEPs.

 

 

 

 

 

COURSE OBJECTIVES

  • Identify, analyze and manage process risk at early stage of facility design
  • Understand and apply basic inherent safer design principles at the design and engineering stages of offshore facilities
  • Understand and apply best industry safety and engineering REGAGEPs in ensuring safety in production operations
  • Understand recommended best industry practice and standardized method to design, install, and test surface safety systems on production platforms.
  • It will help participants to verify conformance with the recommended practice.
  • Understand the methods that can be used to determine safety requirements to protect any process component.
  • Apply various RAGAGEPs discussed during the training at work place and to prevent or mitigate inherent process risks.

 

TARGETED AUDIENCE

Operators of offshore and onshore oil and gas facilities

  • Process engineers
  • Production engineers
  • Loss Prevention Engineers
  • Process safety engineers
  • Occupational health and safety professionals
  • Facility engineers
  • Project engineers & managers
  • Offshore Superintendents & OIMs
  • Professionals involved in the design phase of facility design
  • Maintenance and operators of production facilities etc

 

 

 

DESIGN OF BASIC SURFACE SAFETY SYSTEMS FOR PRODUCTION PLATFORMS

 

MODULE-1  CODE: DBSMOD-1   Duration- 2 Days   Fee- N80, 000  Date: 8-9 Oct 2018.

 

 

 

 

 

 

 

 

 


 

 

 

 

 

 

 

 

 

 

 

 

SAFETY IN DESIGN FOR LIVING QUARTER AND

PROCESS AREA OF PRODUCTION FACILITY

 

MODULE-2   CODE:SIDLQMOD-2  Duration- 2 Days   Fee- N80, 000  Date:10-11 Oct,2018

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 


 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COURSE REGISTRATION

 

Option-1 (Complete Course package)

 

 

Candidate may wish to register for the full package or complete course. This is made up of 3 modules and will run for 5days.Candidate must take the full course (5days) before he or she will be issued a certificate of training for the full package.

 

Module-1: DESIGN OF BASIC SURFACE SAFETY SYSTEMS FOR PRODUCTION PLATFORMS

 

Module-2: SAFETY IN DESIGN FOR LIVING QUARTER AND PROCESS AREA OF PRODUCTION

                       FACILITY

 

Module-3: FIRE PROTECTION SYSTEM DESIGN CONSIDERATION

 

 

 

Option-2

Alternatively, candidates could also register for any of the 3 modules separately and completion certificate of training will be issued for each or separate module completed.

 

Course Fee:

Module1-3 (5days): Course fee for the complete course package is N200, 000                 per participant

 

Fee for Separate Course Modules

Module -1 (2days): N80, 000 per participant

 

Module -2 (2days): N80, 000 per participant

 

Module-3 (1day):   N40, 000 per participant

 

 

A comprehensive and quality handout and a certificate of completion will be given to participants at the end of the training.

 

CONTACT:

For registration details, kindly contact; emmanuel@dmsheffieldng.com, info@dmsheffieldng.com, infodmsheffield@gmail.com

Mobile: 08141622363

 

Payment shall be made into’

DM SHEFFIELD LIMITED

3592050687

ECOBANK